1060 Route 47 South
Rio Grande, NJ 08242

Phone: 800-462-1209
Local:   609-886-0416
Fax:      800-231-5422
Showroom Hours:
Tue - Fri: 10am - 5pm
Sat:         10am - 4pm

Office/Phone Hours:
Tue - Fri: 8:30am - 5pm
Sat:            10am - 4pm
Sun - Mon: Closed
 

    
WHOLESALE | CATALOG REQUEST | JOIN MAIL LIST | ABOUT US | DIRECTIONS | SIGN GUESTBOOK | EMAIL US | VIEW CART | HOME

 Gryphon Saws and Sander

Gryphon Zephyr Ring Saw
Gryphon Zephyr Diamond Ring Saw

The Gryphon Zephyr Diamond Ring Saw offers advantages not found in other glass saws.

The round blade can cut in any direction, and operation is very smooth and quiet. The Zephyr saw has a large work surface that is free of obstructions. The overhead blade support is slender, allowing the artist to have a very clear view of the material as it is cut. In addition, the Zephyr has a deeper throat and more clearance for the glass than other consumer glass saws.

Special attention has been given to designing the saw for quiet operation and for low maintenance. The critical moving parts are shielded to minimize the abuse from the glass dust that is generated when cutting. The highest quality bearings and wheels are used to extend the life of these critical parts.

The motor/blade assembly is a separate unit that can be removed from the base and used as a hand-held saw. This is useful for cutting items that cannot easily be brought to the table. A small water reservoir is built into the blade assembly housing and will hold enough water for a few minutes of hand-held cutting. When the saw is used in the normal configuration (installed in the base), the base will hold enough water for several hours of cutting.

The Gryphon Zephyr will cut glass, tile, rock and all other similar hard materials.

Specifications: 3000 rpm - 1/3 hp - 18"x18"x11" Weight 19 lbs - Coolant: Recirculating Tap Water - 1 Year Warranty - Made in USA

 

Special Deal! 

Purchase a Zephyr Saw for $299.95 and Receive 4 Free Pattern Books!
Over $50 of books for FREE and save $80 off the Saw!
 

Features

  • MUCH quieter operation
  • 20% deeper throat (6 5/8” vs. 5 1/2”)
  • 2x height clearance (1 1/2” vs. 3/4”)
  • Longer lasting bearings and wheels
  • When used as hand held, not necessary to attach separate housing cover

# 08515   Gryphon Zephyr Diamond Ring Saw List:  $ 379.95 $ 299.95 Buy
# 08516 Standard Diamond Replacement Blade List:  $ 59.95 $   59.95 Buy
# 08517 48" Drive Belt Kit - Includes Upper & Lower Wheel Bands and one set of Lower Wheel bushings List:  $ 29.95 $   24.95 Buy
# 08518 Purple Idler Wheel with Bushings List:  $ 22.95 $   19.95 Buy
# 08519 Set of 3 Rubber Inserts for Gold Drive Wheels List:  $ 14.95 $   12.95 Buy
# 08520 Gold Guide Wheel with Bearing List:  $ 24.95 $   21.95 Buy
# 08521 Fine Dichroic Blade - for delicate work, leaves very smooth edge List:  $ 59.95 $   59.95 Buy
# 08522 Separating Blade - enables making inside cuts without having a lead-in cut List:  $ 59.95 $   59.95 Buy
# 08523   Replacement Face Shield List:  $ 12.95 $     9.95 Buy


Gryphon C-40 Diamond Band Saw

The Gryphon C-40 Diamond Band Saw is the ideal tool for your difficult projects. It cuts as easily through heavily rippled glass as it does through the smoothest window glass. Those impossible cuts are made easy - simply guide the glass, and the saw does the rest. With our new high-speed motor, you will breeze though your projects at a surprisingly fast pace.

Highlights:
• You cut faster - the blade travels at 40 miles per hour
• Direct drive - no belts or pulleys
• New upper blade guide provides increased control while cutting
• New saw and wheel design reduces basic saw maintenance to near zero
• Huge water reservoir under the work surface
• Less waste because tighter blade tensioning allows more precise cutting
• One square foot of unobstructed work surface
• Blade Dimensions - 37 inches in diameter, .020 inches wide, .140 inches deep
• Tension Adjustment - Single knob - Semi-automatic

Specifications: 2850 rpm - 1/3 hp - 18"x18"x11" Weight 18 lbs - Coolant: Recirculating Tap Water - 1 Year Warranty - Made in USA

# 08400   List: $ 379.95   $ 297.95    Buy

# 08401    C-40 Replacement Blade Twin Pack     $ 97.95    Buy

# 08402    C-40 1/4" Super Power Fuser's Blade   $ 67.95    Buy

 

 Gryphon C-40 Diamond Bandsaw

Gryphon Miter Saw
 

Specifications: 5500 rpm - 115 volts AC - 1.1 hp - 
Weight 15 lbs - 1 Year Warranty

Abrasive Miter Saw

 

The Gryphon Miter saw is particularly well suited for making premium cuts in thin wall extrusions of brass, zinc, steel and copper. It has a very fine abrasive blade which cuts cleanly and coolly resulting in a minimum of flash.

The saw is used largely in the stained glass (for cutting came and zinc used to join separate pieces of glass) and the automotive fields (for cutting tubing of all types including braided stainless hose). A large adjustable table provides settings for accurate angles. The chop saw design along with the built in clamp for the work and safety shield provide protection to the operator.

See the saw in action by watching our videos on your computer screen.
PDF spec sheet

Features

  • Simple construction
  • Powerful 1.1 peak hp direct drive motor
  • Large work surface
  • Adjustable angle of cut with protractor scale for repeatability
  • Thumbscrew clamp to hold work securely to fence while cutting
  • Ultra-thin abrasive blade provides very clean and quick cuts
  • Made in USA
  • Easy one-hand operation
# 08552 Gryphon Miter Saw  
             Reg. $249.95		 $ 221.95 Buy
# 84121 Replacement Abrasive Blade $ 10.95 Buy
# 84122 Replacement Toothed Blade $ 13.95 Buy

 
Gryphon Wet Belt Sander/Grinder

This new product by Gryphon presents an entirely new category of tool for the glass artist.

With a large grinding belt, offering a huge 90 square inches of grinding surface, you can now accurately grind straight lines or true up large curved surfaces quickly and easily. A small platform helps steady your work and tilts for easy beveling. A variety of belts are available from coarse for fast grinding to ultra smooth for polishing.

Features

  • High Speed DC Motor For Fast Grinding
  • Simple construction with few moving parts
  • Direct Drive - No Belts or Pulleys
  • Convenient water reservoir under the lower wheel
  • Uses a standard kitchen sponge to keep the belt wet
  • Ruggedly constructed of high-impact plastic, aluminum & steel
  • Comes with 3 belts (80, 120, & 400 Grit)

# 08551   List: $249.95    $ 221.95    Buy
 

Gryphon Wet Belt Sander
Specifications: 3500 rpm - 3” x 30” Belt -
Adjustable for angles - 9.5” x 7.5” Coolant reservoir -
Single Knob Tension Adjustment - Weight 16 lbs -
1 Year Warranty

# 08495  80 Grit Belt  (2-Pack)    $ 16.29    Buy
# 08496  120 Grit Belt  (2-Pack)  $ 16.29    Buy
# 08497  400 Grit Belt (2-Pack)    $ 16.29    Buy
# 08498  Cork Polishing Belt (1)   $ 11.95    Buy
             (Great for polishing edges of cabochons)